Phares Electronics T6 Panel Mount Tachometer
The Phares Electronics Panel Mount Tachometer Model T6 monitors over speed, under speed, zero speed and at-speed conditions, utilizing a 4 or 5 digit display, 0-10V and 4-20mA output signals and 3 SPDT independent isolated relay outputs for speed condition status.
The Phares Electronics T6 Panel Mount Tachometer helps prevent equipment damage and material spoilage via prompt alert for stalled (zero speed) or under speed condition. It is particularly useful for monitoring under speed conditions as this often indicates an unexpected increase in load which may indicate that an unwanted stoppage is about to occur.
The T6 Panel Mount Tachometer uses frequency input from various types of sensors to determine the presence of motion or the lack thereof. When motion is either detected or reaches set point, the relay output(s) change state. They remain in this state until either under speed or zero speed condition occurs (depending upon application). The 0-10V and 4-20mA analog output signals are proportional to speed.
The Panel Mount Tachometer Model T6 features universal sensor input: NPN or PNP, 2 or 3 wire sensor.
Sensor types compatible with the Phares Panel Mount Tachometer Model T6:
Phares Panel Mount Tachometer Model T6 Part Numbers
|T6-A||100-240 VAC||PNP or NPN, 2 or 3 Wire||Qty. of 3, N.O./N.C.||0-10V and 4-20mA|
|T6-D||9-36 VDC||PNP or NPN, 2 or 3 Wire||Qty. of 3, N.O./N.C.||0-10V and 4-20mA|
For answers to any questions you may have, including pricing, availability and tech support, please call us at (727) 444-0406. When you call, you will reach someone at our company who is very knowledgeable regarding our products and will get answers to your questions promptly. If you prefer email, we will respond to your message!
Available locally at CED/Raybro Tampa, FL
CAN/CSA C22.2 No. 61010-1:2012
Part No. T6-A: 100-240 VAC, 50/60 Hz, 50mA
Part No. T6-D: 9-36 VDC, 140mA
1/2 A Max., Input Power, Fuse F4
3 A Max., Relay Common, Fuses F1-F3
Seven Segment LED, 4 Digit, with decimal point.
Ranges: 0-99,999, 0-9,999, 0-999.9, 0-99.99, 0-9.999
LED Height: 0.50″
1.6875″ H x 3.5625″ W x 5.3750″ D
Depth measurement includes terminal blocks.
Cutout Dimensions: 1.75″ H x 3.60″ W, +/- 0.025”
+/- 2 Least Significant Digits
Analog Outputs, Scaled:
4-20mA, T6 Tachometer internal power 24VDC, 250 or 500 Ohm load
4-20mA external power @ 24VDC, 250 or 500 Ohm load
4-20mA external power @ 12VDC, 250 Ohm load
4-14.60mA external power @ 12VDC, 500 Ohm load
Universal Signal Input:
24VDC, Sinking or Sourcing, NPN or PNP, 2 or 3 Wire
Sensor Input Current:
Quantity of 3, each with 1 NO/NC (Form C)
Contact Rating: 3A @125 VAC
Aluminum enclosure, gasketed, with side mounting bars for control panel installation. When properly installed, gasket will provide a NEMA 4 type seal.
Figure 1. Phares T6 Tachometer Front.
The front of the Phares T6 Tachometer is designed and built for use in wash down areas
There are four LED’s on the face of the Phares T6 Tachometer:
- R1 – Relay 1, when illuminated, Relay 1 is engaged.
- R2 – Relay 2, when illuminated, Relay 2 is engaged.
- R3 – Relay 3, when illuminated, Relay 3 is engaged.
- S – Sensor, when illuminated, Sensor is detecting target.
There are four keys on the face of the Phares T6 Tachometer located below the 4 digit display:
- Arrow Up – Increase Parameter Value
- Arrow Down – Decrease Parameter Value
- P – Program, press to advance to the next Parameter
- S – Set, press to access Parameter Value